SC Code on Samsung Washer means that your washing machine has a drainage problem. Specifically, it means that the washing machine has detected that the drain cycle is taking too long. The SC error code is similar to Samsung error codes Nd, 5E, SE, 5C, SC, and 1 5C, which indicate drainage problems. Resolving an SC trouble code is usually as simple as clearing a blockage in the drain hose, pump filter. Or drain pump. To fix the problem, make sure the drain hose is installed correctly please.
If you don’t have time to fix the error, turning off the power for 1-2 minutes usually fixes the error. However, the error code is likely to indicate a problem that needs fixing. And ignoring the error code for too long can make the problem worse in the future.
A 5E or 5C error code indicates that the washer has detected a drainage problem. The most common cause of this error is a clogged filter or a kinked drain hose. You should also make sure the drain hose is properly installed and clean the hose thoroughly to remove any blockages that may be preventing the washing machine from draining.
Samsung washing machine error code SC is actually a 5C error code. With 5 looking like S depending on the model. If your Samsung washing machine has an SC (5C) error code. Your washing machine may be having drain problems due to a clogged pump, drain pump filter, or drain hose.
Table of Contents
Fixing SC Code on Samsung Washer
The washing machine drains water via a pressure switch that detects when the drum is full. Code C0035 If the drain does not start, the self-diagnostic system will display the Samsung washing machine error code SC (5C), 5E, or nd. Older models (manufactured before 2007) have E2.
Cleaning the pump filter (front-loading washing machine)
Many Samsung front-load washers have a pump filter or dirt filter that can be accessed from the front of the washer. Samsung recommends cleaning the pump at least once a month, or after 40 wash loads. Keeping your pump filter clean helps prevent odors, mildew, and mildew and ensures your washing machine drains properly.
Check drain hose
If your washer won’t drain, the drain hose may be kinked, pinched, or clogged with something small. Also, the drain hose outlet may have been soaked, limiting the washer’s ability to drain. If the drain hose is clogged or cannot be connected properly, it must be replaced.
Checking the drain pump
If the drain hose is not clogged, it may be due to a faulty drain pump. Small objects, pieces of clothing, or damaged impellers can cause mechanical failure of the pump. If the impeller is not damaged and the pump is not blocked, you may have an electrical fault.
Other causes
If checking the filter, drain hose, and drain pump does not resolve the issue. The pressure switch may be stuck or failing. A pressure switch tells the control board when to drain or add water. If the control board is receiving an erroneous signal, it may not be draining properly as it thinks it is not needed.
How do you test a washing machine water pump?
Eliminate the channel hose by unscrewing the braces holding it to the siphon outlet. Code C0035 Search for blockages inside the hose, says Family Jack of all trades. To check it, you need to disconnect the belt connecting it to the drive motor.
Giving close consideration to how your clothes washer functions during a customary cycle will assist you with pinpointing whether you disapprove of your channel pipe. On the off chance that the machine turns on and you hear the water siphon, however no genuine water shows up, then, at that point, you no doubt have an obstructed channel hose.
A common grievance is that the water in the clothes washer drum won’t deplete, or that the clothes washer has stopped mid-cycle with it actually loaded with water. Another common issue is that the clothes washer drum won’t turn, or it won’t deplete as expected.
Can a washer drain pump get clogged?
On the off potential for success that there is having water in the washer tub following the last twist cycle. Or there is water spilling from the bottom of the washer cupboard. The washer’s channel siphon or channel hose could be obstructed or broken and keeping the water from being discharged from the machine into a clothing tub or standpipe.
A clothes washer not depleting can have various causes. Including an obstructed or stuck channel hose or a messed up siphon, top switch, or belt. Regardless of the guilty party, you really want to empty the water out of the clothes washer prior to diagnosing the issue or accomplishing any work to cure the situation.
In the event that the washer won’t deplete or turn. Either something is caught in the clothes washer channel hose or siphon, or the siphon is broken. On the off chance that a washer won’t deplete or turn, the fix is basic on the off chance that you’re even a tiny bit of spot helpful with tools.